Guides

How Many Logs Fit in a 20ft or 40ft Container? Counts by Size

A 20ft takes about 18 to 22 CBM of round logs, a 40ft 37 to 44. Log counts by diameter and length, the formula, and the weight check for dense species.

Punj Shah

“How many logs fit in a container?” has no single answer, because it depends on the log size. A container takes a fixed amount of CBM, and the number of logs is that CBM divided by the volume of one log. This guide gives you both: the CBM a container really takes, and a count table you can read off by diameter and length.

Step 1: How much CBM actually fits

Round logs leave gaps between each other, so they fill only part of the box. Using the planning fill range from our container loading guide:

ContainerInternal volumeRound logs at 55-65% fill
20ft33.2 CBMabout 18 to 22 CBM
40ft67.7 CBMabout 37 to 44 CBM
40ft High Cube76.3 CBMabout 42 to 50 CBM

Sawn timber in strapped packs fills more (75 to 85%), so it carries more CBM in the same box.

Step 2: Volume of one log

Use true volume, which is Huber’s formula, the volume of a cylinder at the middle of the log:

Volume (m³) = 0.7854 x diameter² x length

with the diameter in metres and the length in metres. A log 30 cm across and 4 m long is 0.7854 x 0.30 x 0.30 x 4.0 = 0.283 m³. If your tally uses girth instead, see Huber’s formula. Do not use Hoppus volume here: it is about 21% lower than the real space the log takes (see Hoppus vs true volume).

Step 3: Log counts by size

The counts below assume a loadable 20 CBM in a 20ft, 40 CBM in a 40ft and 45 CBM in a 40ft High Cube, the middle of the ranges above. Lengths are limited to 5.8 m so they fit a 20ft (internal length about 5.9 m).

Mid diameterLengthVolume per log20ft40ft40ft HC
20 cm2.5 m0.079 m³254509572
20 cm4.0 m0.126 m³159318358
20 cm5.8 m0.182 m³109219246
30 cm2.5 m0.177 m³113226254
30 cm4.0 m0.283 m³70141159
30 cm5.8 m0.410 m³4897109
40 cm2.5 m0.314 m³63127143
40 cm4.0 m0.503 m³397989
40 cm5.8 m0.729 m³275461
50 cm2.5 m0.491 m³408191
50 cm4.0 m0.785 m³255057
50 cm5.8 m1.139 m³173539

Real containers carry mixed sizes, so for a real load add up the true CBM of the logs on your tally and compare it with the loadable CBM, rather than counting logs.

Step 4: The weight check

Fill is not the only limit. A 26-tonne payload is a planning figure, and the CBM it allows depends on the species:

WoodDensityCBM at a 26-tonne payload
Light softwoodabout 500 kg/m³about 52 CBM
Teak (dry)about 700 kg/m³about 37 CBM
Dense hardwoodabout 900 kg/m³about 29 CBM

So a 40ft of teak is held to roughly 37 CBM by weight, below the 44 CBM the fill range would allow. Always take the smaller of the fill limit and the weight limit. Payload limits and wood densities vary, so confirm the payload with your forwarder and use real density figures for your species.

Worked example

You are loading round teak logs, 30 cm mid diameter, 4 m long, into one 40ft container.

  • One log: 0.283 m³
  • Fill limit: about 40 CBM, so about 141 logs
  • Weight at 700 kg/m³: 141 x 0.283 x 700 = about 27,900 kg, over a 26-tonne payload
  • Weight limit: 26,000 / 700 = 37.1 CBM, so 37.1 / 0.283 = about 131 logs
  • Plan for about 130 logs, not 141

Mistakes that cost money

  • Counting logs instead of CBM. Logs vary in size, so only the true CBM total tells you whether the load fits.
  • Using sawn-timber fill figures for round logs. The container will not close.
  • Ignoring weight for dense species. The load is overweight and is stopped at the port.
  • Planning to the theoretical maximum. Leave a margin for a log that measures larger than tallied.
  • Mixing Hoppus and true volume. Always plan the space with true volume.

Keeping the load plan and the tally on the same numbers

A load plan is only useful if the tally behind it is accurate. LumberLinq records each log’s measurements on your phone, even without a signal, and totals the true CBM per container, so the plan, the packing list and the invoice come from the same figures. Start free or request a demo.

Planning figures only. Container dimensions, fill, payload limits and densities vary by carrier, route, species and how the load is stacked. Confirm the exact figures with your shipping line and forwarder.

Related: Container loading calculation for timber · How many sheets of plywood fit in a container · CBM calculation for round logs

how many logs in a containerCBM per containerround log loading20ft container40ft containerlog volumetimber export

Ready to simplify your timber ops?

Start free - no credit card required.