The quarter girth formula is the quickest way to get the volume of a round log with a tape and a calculator. It is the standard in the teak and hardwood trade in India and Myanmar and in older Commonwealth timber trade, and it is a common reason two people get different volumes for the same log.
This guide gives the formula, worked examples in metric and in feet and inches, a ready reckoner, and the traps to avoid.
The formula
Metric (girth in cm, length in metres):
Volume (m³) = (girth ÷ 4)² × length ÷ 10,000
Feet and inches (girth in inches, length in feet):
Volume (Hoppus cubic feet) = (girth ÷ 4)² × length ÷ 144
“Quarter girth” means one quarter of the distance around the log. Squaring it treats the log as if its cross-section were a square with that side. A real cross-section is round, which has more area than that square would suggest, so the formula under-reads a little on purpose. That is why the quarter girth result is always 78.54% of true volume. See Hoppus vs true volume for the full comparison.
How to measure
- Girth at mid length. Put the tape around the log halfway along its length, not at the thick end.
- Over or under bark. Over bark is the usual default. If the contract says under bark, deduct the bark thickness first, or agree a percentage.
- Length. Measure along the log, to the end of the sound wood, in the unit your formula uses. Say in the contract whether trimming allowance is included.
- Round the girth down to the nearest whole cm (or inch) if that is the agreed practice. Be consistent across the whole shipment.
Worked example 1: metric
A log with a mid girth of 120 cm and a length of 3 m.
- Quarter girth: 120 ÷ 4 = 30 cm
- Squared: 30 × 30 = 900
- × length: 900 × 3 = 2,700
- ÷ 10,000 = 0.27 m³
For comparison, true (Huber) volume is 120² × 3 ÷ 125,660 = 0.344 m³. The quarter girth figure is 21.5% lower.
Worked example 2: feet and inches
A log with a mid girth of 48 inches and a length of 10 feet.
- Quarter girth: 48 ÷ 4 = 12 inches
- Squared: 144
- × length: 144 × 10 = 1,440
- ÷ 144 = 10.0 Hoppus cubic feet
In metric that is 10.0 ÷ 35.315 = 0.283 m³ of Hoppus volume.
Ready reckoner: 4 m logs
Volume of a 4 m log by mid girth (over bark). The quarter girth column is the figure you would write on a Hoppus tally. The last column shows the same log in Hoppus cubic feet.
| Mid girth | Quarter girth m³ | True (Huber) m³ | Hoppus CFT |
|---|---|---|---|
| 60 cm | 0.090 | 0.115 | 3.2 |
| 80 cm | 0.160 | 0.204 | 5.7 |
| 100 cm | 0.250 | 0.318 | 8.8 |
| 120 cm | 0.360 | 0.458 | 12.7 |
| 140 cm | 0.490 | 0.624 | 17.3 |
| 160 cm | 0.640 | 0.815 | 22.6 |
| 180 cm | 0.810 | 1.031 | 28.6 |
| 200 cm | 1.000 | 1.273 | 35.3 |
For any other length, scale the figure in proportion: a 2 m log of the same girth has half the volume of a 4 m log.
Add up a lot
Quarter girth is applied log by log, then the volumes are added. Do not average the girths and square the average, because squaring does not average out: a few big logs would be under-counted. On a tally sheet that means one row per log with its girth and length, and a total at the bottom. Ten logs of 110 cm girth and 3.2 m length make 2.42 m³ by quarter girth (3.08 m³ true).
Common mistakes
- Squaring the girth instead of the quarter girth. That gives a number 16 times too large.
- Mixing units. Girth in cm with length in feet, or inches with metres, gives nonsense. Convert first.
- Mixing Hoppus feet and cubic feet. They differ by 27%. Never put both on one document without labelling.
- Averaging girths. Calculate each log, then add.
- Not saying which convention is used. A buyer expecting true volume will count 27% more than your Hoppus total. Write the formula into the contract.
Keeping the measurement, not just the answer
The quarter girth figure is only useful while the girth and length behind it are still on file. LumberLinq records girth and length as your staff tally on the phone, calculates round log volume in CBM and CFT, and keeps the raw measurement so a buyer can ask for the other convention without re-measuring. Start free or request a demo.
Related: Free timber volume calculator · Hoppus formula vs true volume · Huber’s formula for log volume · Timber tally sheet format and free template