A mill saws 12 CBM of logs and ends the week with 6.6 CBM of boards. Is that good? Nobody can say until the number is defined: out of what, measured how, and compared with what.
Outturn (also called recovery or yield) is the simplest and most useful number in a sawmill. This guide gives the formula, a worked example, the places the rest of the log goes, and one trap that makes mills look better than they are.
The formula
Outturn % = sawn timber volume out ÷ log volume in × 100
Both volumes must be in the same unit (CBM or CFT) and measured the same way. Everything else in this post is about keeping that sentence true.
The same idea, seen from the loss side:
Conversion loss % = 100 − outturn % (or: volume in − volume out, divided by volume in)
A worked example
A mill runs one batch of teak logs through the saw.
| Item | Volume |
|---|---|
| Logs in (true volume, Huber) | 12.00 CBM |
| Sawn timber out (thickness × width × length × pieces) | 6.60 CBM |
| Outturn | 6.60 ÷ 12.00 = 55% |
| Conversion loss | 5.40 CBM, or 45% |
If your logs were measured by Huber’s formula, the log volume is true volume. If they were sawn timber volumes calculated from thickness, width and length, the output is true volume as well. Both sides match, so 55% is a fair number.
The trap: Hoppus makes outturn look 27% better
Many mills in the Indian and teak trade record log volume on the Hoppus (quarter girth) basis. Hoppus volume is 21.46% lower than true volume, so the denominator shrinks.
Same logs, same boards:
| Basis for log volume | Log volume in | Sawn out | Outturn |
|---|---|---|---|
| True volume | 12.00 CBM | 6.60 CBM | 55.0% |
| Hoppus (12.00 × 0.7854) | 9.42 CBM | 6.60 CBM | 70.0% |
Nothing about the sawing changed. The percentage rose from 55% to 70% only because the logs were measured by a convention that counts less wood. Comparing a mill that reports on Hoppus with one that reports on true volume is meaningless unless you convert first.
Rule: write the log volume convention next to every outturn figure, and never compare two figures that use different ones.
Where the other 45% goes
A log is round and the product is rectangular. Rough guide to where the volume leaves:
| Loss | What it is |
|---|---|
| Kerf (sawdust) | The saw blade turns a strip of wood into dust at every cut. A thinner blade means less dust on every cut. |
| Slabs and edgings | The curved outer parts of the log that do not fit inside a rectangle. The biggest loss on small and tapered logs. |
| Trimming | Ends squared off, and boards cut to standard lengths. |
| Defects | Rot, large knots, splits, shake, and damage cut out. |
| Drying shrinkage | Only if you measure after drying. Boards measured green and again after kiln drying come out smaller. |
Slabs and edgings are often usable as firewood, chips or smaller pieces. Whether that counts as “recovery” is a decision to make once and write down.
What changes outturn
- Log size and shape. Larger, straighter logs give a higher share than small, crooked ones. This is why one outturn number for “the mill” is not very useful.
- Species. Density, defects and how the grain behaves differ.
- The product being cut. Square-edged boards versus specific cut sizes versus flitches give different results.
- The saw. Blade thickness, blade condition, and band saw versus circular saw.
- The operator and the cutting pattern. Two operators on the same logs on the same saw can differ by several percentage points. That is the number worth finding.
- What you call output. Whether trimmed, sorted and graded stock counts, or only grade A.
There is no single “good” figure that applies across mills. As a loose picture, many mills land somewhere between about 40% and 60% of log volume, but treat that as a range to place yourself in, not a benchmark to chase. Your own history by species and log size class is the useful comparison.
What to track so the number means something
- Per run, not per month. A monthly average hides the bad run and the good operator.
- Log volume in, by convention. True or Hoppus, written down.
- Sawn volume out, by product and grade.
- Species and log size class.
- Operator and saw.
- Date and any note, such as blade changed or very defective lot.
After a few weeks you can answer practical questions: Which species loses the most? Does sorting logs by size before sawing help? Is one saw consistently lower?
Conversion loss from sawing is expected. It is not the same as stock that went missing. When you reconcile a consignment, a mill’s normal conversion loss has to be separated from real shrinkage, or every processed shipment will look like a loss.
Doing this in LumberLinq
LumberLinq records a mill job with the logs going in and the sawn timber coming out, and shows the outturn on the spot, before the job is closed. Each run is tied to the operator who ran it, so average and best outturn per operator build up from real history instead of memory. Volumes are calculated from the measurements as your team enters them, so the input and output always use the same convention.
Start free or see it in 15 minutes.
Frequently asked questions
What is outturn in a sawmill? The share of log volume that comes out as sawn timber: sawn volume out ÷ log volume in × 100. Also called recovery or yield.
What is a good recovery percentage? It depends on species, log size, quality, product and saw. Many mills fall between about 40% and 60%. Your own history by species and log size is a better benchmark than an industry average.
Why does Hoppus make the number higher? Hoppus counts 21.46% less wood than true volume for the same log. The same boards divided by a smaller volume give a percentage about 1.27 times higher. Always say which convention was used.
How do I improve recovery? Measure it per run first. Then look at sorting logs by size, a thinner kerf, the cutting pattern for each log, and comparing operators on similar logs.
Related: Hoppus vs true volume · Huber’s formula explained · How to calculate the volume of sawn timber · How to reconcile a timber consignment · Free timber volume calculator